LM    Topics 

Manufacturing remains on right side of growth again in April, reports ISM


Manufacturing activity in April remained on the right side of growth for the second straight month, following six months of contraction, according to the April edition of the Manufacturing Report on Business from the Institute for Supply Management (ISM).

The PMI, the index used by the ISM to measure growth, was 50.8 (a reading of 50 or higher indicates growth) in April, which was down from March’s 51.8. From October through February, the PMI had seen sub-50 readings, with October marking the first month that the PMI was below 50 since November 2012. April’s PMI is 0.4 percent above the 12-month average of 50.4. ISM noted the over all economy has seen growth for 83 months in a row.

Including the PMI, one of the report’s key metrics was up in March. New orders, which are often cited as the engine that drives manufacturing, were off 2.5 percent at 55.8, still a very strong number and growing the past four months, and production saw a 1.1 percent decline to 54.2, while also still growing over the last four months. Employment up 1.1 percent to 49.2 and remained in contraction mode for the last five months.

ISM said that of the 18 manufacturing sectors contributing to the report, 11 reported growth in April, including Wood Products; Printing & Related Support Activities; Paper Products; Plastics & Rubber Products; Primary Metals; Fabricated Metal Products; Chemical Products; Machinery; Computer & Electronic Products; Nonmetallic Mineral Products; and Food, Beverage; and Tobacco Products.

Comments submitted to the report by ISM member respondents were on the optimistic side. A printing and related support activities respondent said activity is increasing as his company moves into the busy season, and a miscellaneous manufacturing respondent explained that business conditions are stable, with sales and production rates steady to improving.

“New orders and production are broadening out their bases of support, with 15 of 18 sectors reporting gains in each category, even though the PMI was down slightly,” said Brad Holcomb, chair of the ISM Manufacturing Survey Business Committee, said in an interview.

April inventories at 45.5 were off 1.5 percent from March, which Holcomb said still represents a conservative inventory management strategy on behalf of manufacturers, with most of them likely being instructed to keep inventory levels down. This movement, he said, is likely pulling the PMI down, while noting that is not necessarily a bad thing.

“I think inventories are going to move up in the future, especially as new orders continue to grow,” he said. “New orders minus inventory for April is at 10.3, following 11.3 in March. It is a pretty strong indicator that we don’t have enough inventory to really support this ongoing level of new orders, assuming that continues.”

Prices jumped up 7.5 percent to 59.0, with all commodities, including those related to oil, showing gains. He cited metals and resins, among those seeing gains that are directly related to oil.

April supplier deliveries at 49.1 were down 1.1 percent from March but showed growth as a reading below 50 for this category indicates growth. And backlog of orders dipped 0.5 percent to 50.5

“If you look at both production and backlog, they obviously work together,” he said. “Production is down a little bit, but backlog is up, which is a good thing as it supports continuing production. Supplier deliveries up and down around 50 is par for the course and sort of going along with the flow.”

While the PMI remained above 50 again in April, IHS Global Insight U.S. Economist Michael Montgomery was bearish in regard to the report.

“The PMI, cooled back down toward mediocrity in April, losing an index point to 50.8 from 51.8,” he stated in a research note. “Orders and production both remained over the 50-mark that separates expansion from contraction, but both lost a bit of ground from the month before, also cooling back to mediocrity. The much-watched export reading firmed by another half point [to 52.5], but the import tally also rose by half a point, to yield no suggestion of an improving net foreign trade picture.”


Article Topics

ISM
Manufacturing
   All topics

Latest in Logistics

LM Podcast Series: Assessing the freight transportation and logistics markets with Tom Nightingale, AFS Logistics
Investor expectations continue to influence supply chain decision-making
The Next Big Steps in Supply Chain Digitalization
Under-21 driver pilot program a bust with fleets as FMCSA seeks changes
Diesel back over $4 a gallon; Mideast tensions, other worries cited
Four U.S. railroads file challenges against FRA’s two-person crew mandate, says report
XPO opens up three new services acquired through auction of Yellow’s properties and assets
More Logistics

About the Author

Jeff Berman's avatar
Jeff Berman
Jeff Berman is Group News Editor for Logistics Management, Modern Materials Handling, and Supply Chain Management Review and is a contributor to Robotics 24/7. Jeff works and lives in Cape Elizabeth, Maine, where he covers all aspects of the supply chain, logistics, freight transportation, and materials handling sectors on a daily basis.
Follow Modern Materials Handling on FaceBook

About the Author

Jeff Berman's avatar
Jeff Berman
Jeff Berman is Group News Editor for Logistics Management, Modern Materials Handling, and Supply Chain Management Review and is a contributor to Robotics 24/7. Jeff works and lives in Cape Elizabeth, Maine, where he covers all aspects of the supply chain, logistics, freight transportation, and materials handling sectors on a daily basis.
Follow Modern Materials Handling on FaceBook

Subscribe to Logistics Management Magazine

Subscribe today!
Not a subscriber? Sign up today!
Subscribe today. It's FREE.
Find out what the world's most innovative companies are doing to improve productivity in their plants and distribution centers.
Start your FREE subscription today.

April 2023 Logistics Management

April 9, 2024 · Our latest Peerless Research Group (PRG) survey reveals current salary trends, career satisfaction rates, and shifting job priorities for individuals working in logistics and supply chain management. Here are all of the findings—and a few surprises.

Latest Resources

Warehouse/DC Automation & Technology: Time to gain a competitive advantage
In our latest Special Digital Issue, Logistics Management has curated several feature stories that neatly encapsulate the rise of the automated systems and related technologies that are revolutionizing how warehouse and DC operations work.
The Ultimate WMS Checklist: Find the Perfect Fit
Reverse Logistics: Best Practices for Efficient Distribution Center Returns
More resources

Latest Resources

2024 Transportation Rate Outlook: More of the same?
2024 Transportation Rate Outlook: More of the same?
Get ahead of the game with our panel of analysts, discussing freight transportation rates and capacity fluctuations for the coming year. Join...
Bypassing the Bottleneck: Solutions for Avoiding Freight Congestion at the U.S.-Mexico Border
Bypassing the Bottleneck: Solutions for Avoiding Freight Congestion at the U.S.-Mexico Border
Find out how you can navigate this congestion more effectively with new strategies that can help your business avoid delays, optimize operations,...

Driving ROI with Better Routing, Scheduling and Fleet Management
Driving ROI with Better Routing, Scheduling and Fleet Management
Improve efficiency and drive ROI with better vehicle routing, scheduling and fleet management solutions. Download our report to find out how.
Your Road Guide to Worry-Free Shipping Between the U.S. and Canada
Your Road Guide to Worry-Free Shipping Between the U.S. and Canada
Get expert guidance and best practices to help you navigate the cross-border shipping process with ease. Download our free white paper today!
Warehouse/DC Automation & Technology: It’s “go time” for investment
Warehouse/DC Automation & Technology: It’s “go time” for investment
In our latest Special Digital Issue, Logistics Management has curated several feature stories that neatly encapsulate the rise of automated systems and...