Subscribe to our free, weekly email newsletter!

Warehouse & DC Management: Moving toward smarter lift trucks


Using sensors to track when a lift truck is in motion, when it is at rest, or when the forks are engaged in lifting and lowering, allows fleet managers to optimize the size of their fleets.

By Bob Trebilcock, Editor at Large
October 01, 2012

Right sizing the fleet
With sensors tracking when a lift truck is in motion, when it is at rest, or when the forks are engaged in lifting and lowering, information is now available to track the utilization of a fleet.

“If you measure how a truck is being used and how much of the time it’s idle, you might find that instead of 10 trucks in the shipping department, you only need eight,” says Toyota’s McKean.
In many facilities, managers assume their fleet is being fully utilized throughout a shift because of the activity that typically takes place within a plant or distribution center. Facilities may also have a mix of equipment based on how work was once performed in the facility, even if products, processes and lines have changed. They might even have more trucks than they realize. Fleet management software provides hard data to back up or refute those assumptions.

“One of our customers told us that he needed more trucks,” recalls Jim Gaskell, director of global Insite products for Crown Equipment. “When we installed the software, he discovered he had two more trucks than he thought he had. They weren’t being used at all.” In fact, it’s not uncommon for a facility to learn that the fleet is only being utilized at 50 percent or so of capacity.

“For instance, we can learn how many operational hours are being used for lift and travel or how many trucks are being used simultaneously,” Gaskell says. “There may be peak periods when they are using all of their equipment, but if that peak only lasts 10 or 20 minutes a shift, you can ask whether they really need those trucks or if they should change their processes.”

Operational information can also provide a real-time view of where in a facility trucks are being used. That allows a supervisor to shift idle drivers in one area to a busy area during peak periods.

Managing operators
The same tracking systems that monitor the performance of the trucks can also be tied to the performance of the operator. “The wireless tracking devices that monitor the usage of a truck also allow us to put operator check lists online, to manage operator licenses, or to monitor the hours required by a particular operator to perform a task,” says Raymond’s LaFergola.

If an operator is picking an order, for instance, the system can track how much travel there was between pick stations or how much time was required to lift or drop off a load. “If a task should take 30 seconds and it’s taking longer, we can take steps to increase productivity,” LaFergola says. “Among the customers that have implemented the system, we’ve seen 3 percent to 5 percent increases in productivity.”

In addition to managing labor, the system can be used to ensure that only qualified operators are on a particular piece of equipment or working in authorized areas. If an operator’s license is past its renewal date, for instance, the system can lock that operator out of a truck. Similarly, if an operator travels into an area where he isn’t authorized to work or impacts something with enough force to damage the truck, the product or a structure, the system can shut down the truck and send an alert to a supervisor to address the situation.

Similarly, the system can be used to control the performance of an operator. “If you have a new operator who is learning to drive, you can limit the travel and lift speeds,” says Gaskell. “No matter what truck he gets on, he’ll be at that reduced performance level until he gets experience.”

Here today, used tomorrow
Despite those capabilities, fleet management software is not yet widely used beyond a tool for managing maintenance.

The problem, say the experts, is that the available data being collected by the trucks is like drinking from a fire hose. “End users are overwhelmed,” says Raymond’s LaFergola. “They don’t know where to start.”

Yale’s DeSutter concurs. “We expected that telemetry and sensors would equip the customers to act on driver accountability and training and to use the data to avoid costs,” he says. “So far, we haven’t seen that.”

LaFergola sees an opportunity for the lift truck industry to provide consultative services: Suppliers and distributors can sift through and analyze the data to show their customers how they can alter their processes to make their operations more efficient. “Our heart and soul is in making lift trucks,” he says. “But we recognize that there is this need. We are working with dealers to move into this solution.”

One example of how this might be done is using data from a customer’s labor or warehouse management systems in combination with the data collected from the fleet management system to improve labor standards.

Toward a smarter lift truck
While few end users are ready to use lift truck data to drive process improvements, lift truck software is already evolving toward a platform for smarter operations.

A combination of software and hardware, for instance, can automate the data collection process and eliminate hand scanning. Available systems use optical scanning technology to automatically scan and read pallet labels when they’re picked up by the truck, associating that specific pallet with that specific truck in the fleet management software.

Since the system is tracking the location of the truck as it moves through the facility, the system can record a putaway or drop location to within the inch without the driver scanning the bar code. That information can then feed the inventory management module in a WMS.

Fleet management software may also be used to improve task interleaving within the warehouse. “Since we know the real-time location of every truck and pallet, we believe we can feed higher quality data to a WMS for better decision making,” says Total Trax’s Van Wormer.

Meanwhile, Jungheinrich has developed several types of warehouse navigation technology for its lift trucks. “We’re integrating the truck with the WMS to help drivers find the most direct routes to get their work done,” explains Michael Wiesenegg, product line manager of warehouse systems for MCFA, which markets Jungheinrich trucks in North America.

In these applications, the layout of the warehouse is programmed into the fleet management software. When the WMS sends a task to an operator, it also sends a file to the truck, telling it where it needs to go. Using the layout drawing, the truck provides turn-by-turn directions to the driver, similar to the GPS system in an automobile.

For narrow-aisle guided truck applications, trucks are outfitted with RFID readers that read transponders installed in the floor in the aisles. When a truck passes a transponder, it knows exactly where it is and calculates the fastest combination of driving and lift speeds to safely and productively get to the right pallet position for the pick. The system is accurate to within 0.4 inches to 1.2 inches.

“We are seeing productivity gains of up to 25% in narrow-aisle systems based on pallet moves per hour,” says Wiesenegg. More importantly, he says, these types of advancements ensure that lift trucks remain an integral part of operations, even as automation makes strides further. “We are always looking at how we can improve product flow in a warehouse,” he says. “As software and lift truck technology advances, we will incorporate more solutions into our trucks.”

About the Author

Bob Trebilcock
Editor at Large

Bob Trebilcock, executive editor, has covered materials handling, technology and supply chain topics for Modern Materials Handling since 1984. A graduate of Bowling Green State University, Trebilcock lives in Keene, NH. He can be reached at 603-357-0484 and .(JavaScript must be enabled to view this email address)

Subscribe to Logistics Management magazine

Subscribe today. It's FREE!
Get timely insider information that you can use to better manage your
entire logistics operation.
Start your FREE subscription today!

Recent Entries

Shippers and other ocean cargo carrier stakeholders should be cheering the announcement made today by The U.S. Coast Guard, as it formally notified the International Maritime Organization through a Declaration of Equivalency that the United States position on SOLAS is that there are multiple methods to submit the combined cargo and container weight (Verified Gross Mass or VGM).

The proposed $4.8 billion acquisition of TNT Express N.V. by FedEx took a major step closer to becoming official today, with the company and TNT announcing today that they have received unconditional approval of the offer from the Ministry of Commerce People’s Republic of China (MOCFCOM).

March shipments at 798,180 trailed February by 12 percent and were down 19 percent annually. For the entire first quarter, shipments were relatively flat annually, rising 0.27 percent to 2,587,988.

OCEMA says it has placed a priority on working with other stakeholders to find operational solutions that will help U.S. exporters, carriers, and marine terminals prepare for the implementation of the SOLAS Verified Gross Mass (VGM) rule.

The first quarter is typically the slowest period of freight demand for LTL carriers. With a few notable exceptions, that was reflected in first quarter earnings reports of the major publicly held LTL carriers.


Post a comment
Commenting is not available in this channel entry.

© Copyright 2016 Peerless Media LLC, a division of EH Publishing, Inc • 111 Speen Street, Ste 200, Framingham, MA 01701 USA