Building the faster, safer AGV

In Japan, Daifuku has developed a high-speed automatic guided vehicle that works with people and lift trucks
By Bob Trebilcock, Executive Editor
May 01, 2014 - MMH Editorial

I won’t say that your typical AGV moves at a snail’s pace. But, at 60 meters per minute – about 2.2 miles per hour - you don’t implement AGVs for speed. You implement them to automate predictable movements from point to point that add little or no value to an operation. Safety is a big reason they don’t move faster: since AGVs often share the road with lift trucks and workers on foot, it’s important to limit their speed. “That also limits productivity,” says Toshisada Mariyama, an assistant manager with Daifuku in Japan.

But what if an AGV could safely travel at three times or more the usual speed limit, say 200 meters per minute, or 7.5 miles per hour, and still operate in the same space as people and lift trucks? What if the AGV could stop on a dime? Could we see something akin to the Ferrari of AGVs? 

That’s a question that was posed to a group at Daifuku and UBIsense, a maker of active RFID technology, by NEDO, Japan’s largest public research and development management organization. Can you create a high speed AGV with safety technology?

Daifuku joined the project in 2011, according to Mariyama. The challenge, he says, wasn’t developing an AGV that could travel at higher speeds. That was the easy part. Rather, it was developing a traffic monitoring system that could track the real-time location of everyone sharing the space inside a designated work area – including people and lift trucks on the move – and then stop the AGVs before any collisions take place

The solution, which is referred to as an area management system for a smart warehouse, brings together several components and technologies. First, the AGVs can only operate at high speeds within a defined work area. Workers, for instance, have to pass through a portal to enter or leave the area. The AGVs are equipped with a 3D laser sensor in front of the AGV running direction that can detect an obstacle 65 feet away and 6.5 feet above by 3D scanning an area. Lift trucks are tracked in real time by ultra wide band (UWB) sensors. Workers were special vests with two UWB active RFID tags. Unlike the RFID technology used for most asset management tasks, which might be accurate to within say 10 feet, UWB tags are accurate to within 30 centimeters, or just under a foot. The tracking system is sensitive enough that it can detect the location of an individual or lift truck based on shadows. The result is that the system controlling the AGV can bring the vehicle to an immediate halt, even when a lift truck comes from seemingly out of nowhere into the automatic vehicle’s path.

“If the AGV can safely operate at higher speeds, we can significantly increase the throughput per vehicle,” says Mariyama. “That may allow an existing application to operate with fewer vehicles or open up new markets for AGVs.” According to Mariyama, the system was tested in a real DC operated by the Ajinomoto Company in Tatebayashi. The company limited the maximum speed of a vehicle to 130 meters per minute, or just under 5 miles per hour. The test, he says, showed that throughput would double at the higher speed.

In February, the system achieved ISO certification and is now available on the market. The next step is to see if the market is ready for the Ferrari of AGVs.

 

 



About the Author

Bob Trebilcock
Executive Editor

Bob Trebilcock, executive editor, has covered materials handling, technology and supply chain topics for Modern Materials Handling since 1984. More recently, Trebilcock became editorial director of Supply Chain Management Review. A graduate of Bowling Green State University, Trebilcock lives in Keene, NH. He can be reached at 603-357-0484.


Subscribe to Logistics Management magazine

Subscribe today. It's FREE!
Get timely insider information that you can use to better manage your
entire logistics operation.
Start your FREE subscription today!

Recent Entries

While the Federal Railroad Administration (FRA) has long stated its goal of having Positive Train Control (PTC) technology installed on 40 percent of its network by December 31, 2015, railroad industry stakeholders have repeatedly stated that reaching that deadline would be a stretch. It now appears that the railroad sector has some members of Congress sharing the same line of thought with legislation rolled out this week that pledges to extend the PTC deadline to 2020.

West Coast port authorities may be overstating the obvious when they decry “business as usual.” But it’s refreshing to see them finally coming around.

Transportation stakeholders reliant on North Carolina’s major seaports are welcoming news this week, which outlines plans to enhance the intermodal and cold chain network in the region.

The index ISM uses to measure non-manufacturing growth—known as the NMI—was 56.9 in February, which was 0.2 percent ahead of January and also 0.1 percent ahead of the 12-month average of 56.8. Economic activity in the non-manufacturing sector has grown for the last 61 months, according to ISM.

Non asset-based third-party logistics (3PL) services and logistics technology services provider Transplace said today that Brooks Bentz has joined the company in a newly-created role as president of Transplace Consulting in conjunction with the launch of the company’s new North American consulting services practice.

About the Author

Bob Trebilcock, editorial director, has covered materials handling, technology, logistics and supply chain topics for nearly 30 years. In addition to Supply Chain Management Review, he is also Executive Editor of Modern Materials Handling. A graduate of Bowling Green State University, Trebilcock lives in Keene, NH. He can be reached at 603-357-0484 or email [email protected].

Comments

Post a comment
Commenting is not available in this channel entry.